I've Documented 63 Lighting Spec Mistakes Worth $14,000. Here Are the 4 That Keep Repeat
-
The core conclusion
-
Why you might trust this log
-
1. Flos IC Lights S vs IC Lights S2—same glass, different guts
-
2. Tracking spotlight adapters—cut to the wrong track
-
3. Giraffe chandelier mounting height—the "we'll set it at install" trap
-
4. Grow light blue vs red—leaking into a decorative lighting order
-
Boundary conditions, and where I still get burned
The core conclusion
Between January 2019 and June 2024, I recorded 63 lighting-spec errors across roughly 340 purchase orders. Total damage: about $14,000 in redo, rush fees, and discounted re-stocking. Of those 63, 41 fell into four stubborn categories: Flos IC Lights S vs S2 confusion, tracking spotlight adapters mated to the wrong track system, giraffe chandelier mounting heights left "for later," and grow light blue vs red spectrum specs leaking onto decorative lighting orders. The rest of this article is how I stopped repeating those four—starting with how I earned the right to write this.
Why you might trust this log
Eight years handling lighting fixtures and specification orders for an interior-fit-out firm. The first expensive mistake came in 2017: 18 Flos IC Lights for a hotel lobby project, ordered as the version I'd seen on the client's mood board. The client wanted dimmable LED. The lamps that arrived were halogen. (The version I'd quoted was IC Lights S. The version they wanted was IC Lights S2. At the time I did not know those were different products.) We re-sourced 14 units at a negotiated restocking rate. About $4,300 in redo, plus a very uncomfortable conference call.
A few years later I started a pre-submission checklist. In the past 18 months alone, that list has caught 47 potential errors before they reached a P.O. But every line on the list exists because I missed it first. Here's the four that cost the most.
1. Flos IC Lights S vs IC Lights S2—same glass, different guts
Visually, the IC Lights S and S2 share the same spherical shape and the same polished or matte finish. That's the trap. The S runs a halogen bulb (rated for relatively high heat, and dimming behavior varies by dimmer). The S2 is an integrated LED at 2700K, dimmable, with a slightly taller base to house the driver. If a spec sheet says only "Flos IC Lights" and no S/S2 designation, you are one call away from a redo.
In 2018, I specified "Flos IC Lights S" for a boutique-fitout because the client's inspiration board showed the halogen-era version. They also wanted dimming scenes. The halogen version dims—but the dimmer compatibility and the heat load on the fixture are a different conversation than the S2's LED driver. We received 22 units, installed 8, and discovered mid-installation that the dimmer panels were configured for the S2 driver spec. We swapped 14 units. With the distributor's goodwill restocking rate, the hit was roughly $2,600 and a three-week delay on the lighting scene walkthrough.
Current checklist line: "Confirm S or S2. Confirm source type (halogen vs LED). Confirm 2700K on the S2. Confirm dimmer compatibility."—and put both product codes side by side on the same spec sheet so the installer sees the difference.
2. Tracking spotlight adapters—cut to the wrong track
Tracking spotlights look universal until you try to click one into a track that doesn't match.
In North America, the common residential/commercial track is the H-type (three-circuit, 120V) or the J-type (European-style). In much of Europe, single-circuit track dominates—and Flos's own track system uses a proprietary profile. If you order a European-spec tracking spotlight and the site has H-track, you won't find out at unboxing. You'll find out at half-installation.
In 2021 we specified 34 tracking spotlights for a restaurant in Toronto. The architect picked a Flos line off a European catalogue—lovely fixture, but a single-circuit base. The project manager ordered H-track adapters from a North American supplier. They didn't mate. We ended up replacing the adapters and part of the track with the correct Flos track profile. About $1,900 in parts and labor, plus a 4-day schedule slip that we absorbed by calling in an electrician on overtime.
Checklist line: "Tracking spotlight—verify track type (H / J / L / Flos proprietary) against the actual installed track profile before submission." Not against the catalogue photo. Against the track on site. (I have been burned by catalogue photos.)
3. Giraffe chandelier mounting height—the "we'll set it at install" trap
The giraffe chandelier design is a favorite for hospitality lobbies and dining areas—it's a statement piece, and the suspension cord is adjustable, which makes it easy to leave the final height "for the site visit."
But "for the site visit" often means the installer leaves the cord at the longest setting because the job is behind and nobody flagged a target height. In 2020, a giraffe chandelier over a dining table hung about 30cm lower than intended. It looked, honestly, a little silly. Guests walked into it. One complained.
Was that a spec error or a spec ambiguity? I've decided it was both. The cost was real: shortening the suspension cord required a scissor lift and a second electrician visit—about $650—and the client was hosting that evening, so it had to happen on the same day.
Checklist line: "Giraffe chandelier—cord length and finished height MUST be on the spec at submission, not at install. Write the target height in mm." "Adjustable" is not a spec. It's a feature.
4. Grow light blue vs red—leaking into a decorative lighting order
This is the one I did not see coming. In 2022 we were handling a mixed-use lobby—decorative lighting (Flos pendants plus tracking spotlights) and an indoor living wall with a dedicated plant light spec.
Somewhere between suppliers, a grow light blue vs red spectrum sheet got sent to the decorative lighting subcontractor. The sub looked at the wavelength ranges, assumed they were color-temperature options for the spotlights, and ordered 5500K fixtures "because blue meant cooler." The plants got a white light with no deep-red output. The decorative area looked, for a few days, like an operating room.
For the record, since this keeps coming up in the inbox: grow light blue (roughly 400–500 nm) drives vegetative growth, and red (roughly 600–700 nm) drives flowering and fruiting. Decorative lighting is a different language entirely—CRI, color temperature (typically 2700K–3000K for hospitality interiors), beam angle, and glare control. They are not the same spec and should never live on the same submission package.
Fix cost: about $1,200 to swap the wrong spotlights, plus the living wall needed it. Three weeks of re-acclimating the plants. (Should mention: the client was very gracious. I was not.)
Checklist line: "Grow light specs and decorative lighting specs travel in separate submission packages. No exceptions." The sub should never hold both documents.
Boundary conditions, and where I still get burned
This information was accurate as of Q4 2024. Flos updates product data sheets and distributors rotate stock, so verify current specs before ordering above 50 units. The track-type portion is North America–specific; if you're specifying in Europe or the UK, the base system is different, and Flos's own track is a category of one. To be fair, most of these errors are preventable by the manufacturer's own documentation—the reason they happen is that the documentation doesn't get read end to end under deadline pressure. My checklist isn't clever. It's just slow enough to work.
And yes—there's at least one category I still haven't solved: the designer who decides on-site that the scene should be warmer than the spec. I'm working on that checklist line. No, really. I'll let you know when it's done.
Discuss a lighting project
Share the application, fixture family, control intent, and timing if this article connects to an active specification question.
Tell Fluence what you are planning
Share fixture type, site conditions, target schedule, and any controls requirements. Our team will route the request to the right specialist.